Stems shaped - Roughly!

Whilst it was forecast for 35 degrees today, it was the first free day for a while so I got going early finishing beveling the second side of the keelson. That went OK so why not have a go at shaping the stems.  Tom Hill had suggested using a range of tools due to the grain changes around keelson/stem join - draw knife, spoke shave and some planing. Maybe it was the heat , but I don't have a drawknife and my spoke shave has not been a happy experience for me so far so I got out the electric plane, installed new blades and took a deep breath.   Managed to get through it OK without demolishing my beautiful ash stems. It's a rough shaping so far and I will do fine tuning with a hand plane and a short piece of planking stock to get flat lands for the glue joints.

I first used some spraky feeding battens to give me a line on the plank edge lands on the stem and punched a mark on the centre line of the stem so I don't lose sight of this through the stem shaping process.

 And here;s the stems from front and side after teh rough shaping with the electric plane.....

Jack Holt's Rambler cruising dinghy

Although I really like the Fulmar design of Iain Oughtred (see previous posts and my experiments with a cruising model of this design) I have become interested in a 1954 design of Jack Holt called the Rambler.  It's 17ft - ideal for my building space and double chime plank on frame (much easier building for me on my own than lapstrake).  I now have plans for Rambler and here's a pic of the sailplan.

A UK small boat designer , Keith Callaghan, has owned one for some years having modified the standard design quite a bit with a modern cabin and cockpit. See more info at

http://www.bluelightning.co.uk/lively/lively.htm

 

Long Winding Bevels

A full day on the canoe today to start beveling keelson and stems. About half the day was spent making the screw in batten to go into my low angle plane.  I needed to make a jig to hold a sliding chuck device which gave me exact perpendicular drilling capability.

I cut a square piece of thick ply and left a projected square bit in the middle to match the base on the sliding chuck stand. Then I clamped a piece of silver ash vertical against my work bench front beam.  This will be the batten for screwing to the plane.  I need to drill a 3/16th  hole exactly vertical into this and exactly away from the edge to match where the screw hole is in the side of the plane.  So I slide the ply base over the top of the ash batten until the drill bit in the chuck is exactly over the marked spot for the hole, then clamp the ply base to the bench and drill.  The set up is shown below.

 Here's the plane with batten screwed in as it will ride the keelson and riband. In this pic it screws flush to the plane but I ended up putting a nylock nut on the end of the screw to control the thread end length to stay constant at what's required to screw into the plane - it had started to reduce and the screw began to disappear into the batten.

So by the end of the day I have one side beveled pretty close to the required winding bevel - being careful to not cut into the centreline.  Still lots more to do on the stems.

....and a nice satisfying pile of long spiral spruce shavings at the end of the day........

Keelson on - Stems Glued - Tent up

There has been some fits and starts with the Charlotte build. Some friends from the Wooden Boat Association also starting builds have applied peer pressure with a mutual guideline - "do at least one thing on the boat project every day".  I got off to a good start but then a few other priorities got bumped up and that "one thing" became just thinking about what I would like to do next on the boat project,  Well I am now on top of these other things and , weather permitting, it's game on with the boat.  I'll try to post more regularly as bits get done. This post covers quite a few things done over the last couple of weeks.

The keelson was cut some weeks ago but before fitting it I champhered the internal edge with a small brass spokeshave (I'll post a pic of this later). Then I sanded the three internal faces.  This is all much easier to do now before the hull is built. Here's a pic of clamping the keelson on the jig and checking for straight.

Then I got to work sanding the faces of the Stems for similar reasons and planing the glue faces  
flat.  I then clamped the stems to the keelson, I cut wedges which matched the curved profile of the stems so that I could clamp perpendicular on both edges. I used some strips of that non-slip mesh used in kitchen cupbords so that when it comes to be glued, the stem won't slide off the mark.  You can see all this in the following pic.

Next step was to mark the shape for a filler piece that goes between the end of the jig and the stem.  This will be glued to the jig but left free at the stem edge and clamped while all the shaping work is going on with the stems.  I made my stems a bit longer than the plans so that I can firmly clamp them to the end projection on the filler piece.  I am also giving myself the option to have higher stem projection on the canoe above sheer for holding it and maybe securing an anchor line.

 Then finally as the sun set today I got the stems glued to the keelson so the actual boat itself is finally on it's way!

And now with the next five days with rain around it's time to erect the canoe tent. I built 5 arch supports from 50mm PVC plumbing tubing and two of these are secured to the tressles holding the jig. You can see the wooden attaching pieces I made with circular cut out to fit the PVC tube. Yes there is a chance of a grey flying canoe house crossing the Tasman (with canoe inserted) if we get a big blow!  But it is easy to dismantle on building days and re-erect and leaves me with room to move around the building jig. The arch supports fit inside one another at the end of the deck and don't take up much space. Here's a couple of shots inside and outside the tent.  I have ridge poles for the sides but didn't get time to fit them today when I took the pic.

   

Building Tom Hill's Charlotte Canoe

Just started my first real boat build after spending lots of time on design modifications on the model of Skye Maid.  Tom Hill's canoe design Charlotte is a great first boat to build for lapstrake design. It has six planks a side, beveled stems and inner and outer gunnels. All the basic elements of small wooden boats. Tom's book "Ultra light Boat Building" and DVD on Charlotte building are a great substitute for boat building school. The plans are a simple one sheet.  I have had the ply for the planks all ready for this for some time.  It's 4mm Bruynzeel Gaboon imported by Andrew Denman in Tasmania.  Target weight for the canoe is 27lb so let's see how close I can get to this.

I copied the mould shapes from the plans onto monofilm.....

..

 .....I've cut out the moulds from 9mm marine ply and will keep the female parts for help in shaping ring frames which I might add to support foot supports and maybe bouyancy tanks (both of which are not part of standard design). 

   The building jig is a bow of two 6 inch by 1 inch planks. I've used finger jointed pine for this which seems a lot harder to spread than what Tom uses in his video. Here I am using reversed clamps to spread my bow - I couldn't make it to Tom's specified breadth but I think it will work OK.

  ...........and after a couple of days I have the jig settled with moulds and stronback attached.

   I'm trying to follow everything pretty close to Tom Hill's methods in his DVD.  I've made trestles like he has and found them very unobtrusive and very useful for stacking clamps and boat pices out of the way.

Cruising Fulmar - More design mods

A few pics to update some modest progress on my design mods for the Cruising Fulmar. For the benefit of those not reading earlier posts, this is to be an 18ft lapstrake cruising cutter based on Iain Oughtred's original design for the Fulmar and with inspiration and modified plans drawn by Kees Prins.  The extra work I am doing is to get more cabin space, have twin rudders stick driven and insert a well  for the outboard.

Re the cabin space, I have decided to push the centreboard aft so that the front of the case sits under the bridge deck and have a dagger board just ahead of the mast step to give lateral resistance matching the sailplan. This means no centreboard case in the main cabin space.  You can hopefully get the idea of this with yhe model pics below with white cardboard in the model representing the centreboard case and forward dagger board case.

Centreboard will sit just under cockpit floor. The two brass tubes drive the twin rudders and will sit just above the cockpit floor.  The centreboard will swing down and not be as wide as standard design but total lateral resistance will also come from the forward dagger board as well as more effective size of rudders area compared to one rudder. The combination of swing centreboard and forward dagger board will allow flexible options to trim balance and set rigs with the three sails of the cutter rig.

...and here you can see the forward dagger board case represented by the white cardboard and teh extra space created in teh main cabin area - bunk soace either side and feet space projecting back under cockpit seats. The square frame (which will be stainless steel)  is mast step support - mast will be in tabernacle on cabin top.  This frame give some central space for (optionally) a seat, a kitchen box/cock top, or a porta poti. 

And now for the cabin. I am experimenting with a stitch and glue structuring of the cabin top. The pics below shows the "chine lines" on which this cabin top will be put together.  I'm in the process of spiling the patterns for the "planks" which make up this cabin top.  The strata in this mock up will not be part of the structure - it's just there to show the lines.  More to come once I have had a go at making the stitch and glue model.

 

Skye Maid lives

Gradually getting some momentum back on the ultimate project - my (approx) 18ft gaff cutter version of Iain Oughtred's Fulmar and Kees Prins' Far Fetch design.  Here's a pic of where I am at right now working on the 1/5th model. I have made a model of the Tohatsu 5HP 4 stroke short shaft outboard and done a cut out in the stern to test how it will dip below keel level and swing out the back.  It's a bit border line as to whether I need to go for the long shaft to get it clearing the transom and I will have to get the well isolated to stop getting pooped in sloppy conditions. You will also notice the final configuration for the push rod steering system, now isolated to the top area of the transom. I'm going to have to lengthen the boat a little bit more to make the cockpit comfortable for two people to windward.  So we are getting close to 18ft now. More work to do on cabin ergonomics. I'm thinking of planning it for single handed comfort with the option of a removable pipe birth for second occupant.  Also looking at an arch support under mast to provide central seating position in front of centreboard case.

  

Lake District Downunder

Living where I do you would think I would have got organised with more real boating activity but I am making steps towards it.  I do a bit of looking at the water even if I am not out on it. A nice walking track is just 5 minutes away beside Narrabeen Lakes.  Here's a pic of the trail I walked this morning taken with my new phone (yes I am slowly climbing into the 21st century).

I though I would have a go at video as well to catch the bird sounds - they were all out this morning, whip birds, owls and others I don't recognise. I captured a few on this video of the vacant launching ramp at the end of the trail awaiting arrival of my yet to build Tom Hill canoe. I thought Dylan Winter might be amused by this one. He's a well known UK sailing blogger who is an expert camerman. When I got home I realised I had taken the video upside down! Well the phone doesn't have a clear Top and Bottom on the case does it? Anyway as luck would have it I was really going to post these pics to talk about the Lakes District Downunder. Whilst it's a mini version compared to the UK lakes district, it hasn't stopped the founding fathers naming nearby streets Windamere, Grassmere etc.  Except for the seagulls dancing on the ceiling you won't notice it's upside down until it gets to the end and the sky and houses come into view - enjoy!  (it's a bit stretch re 16:9 format - I'll improve it later.)

https://www.youtube.com/watch?v=M_1frYzTf0g

Fetching Overarching Articles in Wooden Boat

The arrival of recent Wooden Boat magazine reminded me of how slack I have been on blogging.  Even more embarrassing I've also just noticed John How is getting close to launching his big Fulmar. So thought I should add a few items, even if the boat building hasn't progressed much.

There is a comprehensive article on Kees Prins cruising conversion of Iain Oughtred's Fulmar from page 38 (see index page below). It refers to plans being available from Kees for the modifications I commissioned him to do for a cruising cutter version of his boat - he refers to this as FarFetch. So if you are inspired to have  ago at the boat I am developing you can get the drawings from Kees at keesprins@gmail.com  You will also need the full plans for Fulmar from Iain Oughtred at iain.oughtred@gmail.com

Also in the same Wooden Boat is a life story of NZ born Arch Davis, now ensconced in Maine - it's a wonderful tale many of us latter day boat fanatics would be envious of. His Penobscot designs are stunning.  I wrote away for his DVD of Building the Penobscot 14 to add to my virtual boatbuilding  school and it has many practical demonstrations - I can recommend it as money well spent if you are starting out like me.